Transmission Cooler Replacement Instructions Needed Hello I Here are the instructions on how to replace the transmission cooler and how to refill the transmission when completed. also, i found the part number for the cooler as well. oil cooler 7 speed trans 2115001700 $368.00 9 speed trans 2115001700 $368.00 automatic transmission fluid atf bf27.00 p 1001 01tsc check out the images (below). Start engine while engine is cold. depress brake pedal, place transmission in drive for no more than 10 seconds. stop engine. identify oil return line by feeling both oil lines (3&4). coolest line is oil return line. method 2 (requires an observer) – check oil flow direction (fig c) fig. place container under oil line (3) and disconnect oil.
Transmission Cooler Replacement Instructions Needed Hello I First, change the transmission filter. even a filter that is slightly clogged will reduce the flow of fluid, resulting in higher friction, and friction builds heat. next, consider changing the smooth transmission pan to a finned automatic transmission pan. by building fins into the pan, you increase the surface area that cool air passes by and. Start by removing the top rubber protector from new the radiator support. a door panel tool works great for doing this. next remove the hood latch, this is needed because the 6.0 trans cooler will not fix in without removing the latch, the 7.3 cooler will however come out with the latch in place. Pre installation. identify the two 1 2” npt x 3 8” barb fittings. using teflon tape or suitable sealant, install the two 1 2” npt x 3 8” barb fittings onto the transmission cooler. identify the 11 32” x 4’ hose and hose clamps. slide one hose clamp on each end of the supplied hose. using a dab of oil, lubricate each end of the hose. The below transmission cooler installation diagram shows the transmission fluid flow direction and how the fluid will be routed through a new external cooler. you will need to determine which line is the return for the transmission. you want the already warm fluid to flow into the external cooler to help better control fluid temperatures, so.
Transmission Cooler Replacement Instructions Needed Hello I Pre installation. identify the two 1 2” npt x 3 8” barb fittings. using teflon tape or suitable sealant, install the two 1 2” npt x 3 8” barb fittings onto the transmission cooler. identify the 11 32” x 4’ hose and hose clamps. slide one hose clamp on each end of the supplied hose. using a dab of oil, lubricate each end of the hose. The below transmission cooler installation diagram shows the transmission fluid flow direction and how the fluid will be routed through a new external cooler. you will need to determine which line is the return for the transmission. you want the already warm fluid to flow into the external cooler to help better control fluid temperatures, so. Rags. make sure you have everything ready to avoid interruptions. step 2: lift the car safely. to replace the transmission cooler lines, you need to lift the car so you can access the lines underneath. lifting the car safely is crucial to avoid accidents. start by using a jack to lift the front of the car. Manual. jan 21, 2022. #2. 1 ^^^. transmissions, like engines, work best when fluid temp is between 175 and 195degf (coolant temp for engines) fully warmed up radiator should be about 170 180deg at the bottom or side where the trans cooler is located, so it will cool trans fluid thats above 180degf and keep fluid warmer that's below 170degf. so.
Transmission Cooler Replacement Instructions Needed Hello I Rags. make sure you have everything ready to avoid interruptions. step 2: lift the car safely. to replace the transmission cooler lines, you need to lift the car so you can access the lines underneath. lifting the car safely is crucial to avoid accidents. start by using a jack to lift the front of the car. Manual. jan 21, 2022. #2. 1 ^^^. transmissions, like engines, work best when fluid temp is between 175 and 195degf (coolant temp for engines) fully warmed up radiator should be about 170 180deg at the bottom or side where the trans cooler is located, so it will cool trans fluid thats above 180degf and keep fluid warmer that's below 170degf. so.
Comments are closed.